Spohn Performance 2013 Catalog Now Available

Posted by Spohn Performance | 01/03/13 | Tagged 2. New Products

Spohn Performance 2013 Catalog

The Spohn Performance 2013 catalog is now available. You can download the .pdf catalog by clicking here or order a print catalog by going to this link. You can download the current .pdf price sheet at this link.

.


Rear Bump Stops for 2009-2012 Dodge Ram 1500 4x2 & 4x4

Extended Length Polyurethane Rear Bump Stops
2009-2012 Dodge Ram 1500 4×2 & 4×4

SKU# D09-1500-RBS1 (Product Page Link)

If you have a 2009+ Dodge Ram 1500 4×2 or 4×4 truck and you have lowered the ride height and/or you use your truck for hauling or towing then you need to install extended length rear suspension bump stops.

When the ride height is lowered via air bags, lowering springs or by a heavy load the factory rear bump stops will not properly stop the compression of the rear coil springs before they allow the truck to lay down onto the rear control arms. When this happens it will bend the rear control arms and/or deform and crack the rear control arm bushings.

Our extended length polyurethane rear bump stops will prevent this from happening. They’re an easy 100% bolt in replacement of the factory rear suspension bump stops. Their extended length will stop the rear suspension compression before any rear control arm damage can occur.

These extended length rear suspension bump stops ARE A MUST (not optional) if you are lowered or use your truck for hauling heavy loads and/or towing.

Check out all of our performance suspension components for the 2009+ Dodge Ram 1500 4×2 and 4×4 trucks by clicking here.
.


Rear Upper Control Arm Mount | 1959-1964 Impala, Biscayne, Bel Air
Rear Upper Control Arm Frame Mount
1959-1970 Chevrolet Impala, Caprice, Biscayne & Bel Air

SKU# 640 – 1959-1964 Chevrolet B-Body (Product Page Link)

SKU# 650-6566 – 1965-1966 Chevrolet B-Body (Product Page Link)

SKU# 650-6770 – 1967-1970 Chevrolet B-Body (Product Page Link)

Our rear upper control arm front frame mounts for the 1959-1970 Chevrolet B-Body Impala, Caprice, Biscayne and Bel Air are a direct replacement of the stock mount that attaches the rear upper control arm to the frame.

You can use our new mount to replace the stock mount when it is too corroded or to use as a second mount when installing a four link (two rear upper control arms) set up into a factory three link (one rear upper control arm) car.

Our rear upper control arm front frame mount is CNC laser cut and formed from 3/16″ steel and comes powder coated in gloss black for a brilliant and durable finish.

All necessary mounting hardware is supplied (Grade 8) to complete the installation, including new control arm mounting hardware.

Priced per Mount — Qty. 1 = 1 Mount: You will need to verify whether your car has one or two rear upper control arms. All six cylinder and most small block cars were equipped with one rear upper control arm. Big block cars were equipped with two rear upper control arms.

Fitment Note: Fits Chevrolet B-Body cars only.

Check out all of our performance suspension components for the 1959-1964 and the 1965-1970 Chevrolet Impala, Caprice, Biscayne and Bel Air.

Rear Upper Control Arm Mount | 1965-1966 Impala, Caprice, Biscayne, Bel Air

Rear Upper Control Arm Mount | 1967-1970 Impala, Caprice, Biscayne, Bel Air.


H-Body Vega Monza Panhard Bar Review
CosworthVega.com recently did a review of our Panhard Bars for the 1975-1980 GM H-Body in their latest edition of Cosworth Vega Magazine. You can read the article embedded below or click here to view it on their website.


Ford Torino & Ranchero Rear Upper Control Arms

Tubular Rear Upper Control Arms | 1972-1976 Ford Torino & Ranchero

SKU# FT-607 (Product Page Link)

Our tubular rear upper control arms for the 1972-1976 Ford Torino and Ranchero outperform the flexible and soft rubber bushings that come from the factory. Eliminate wheel hop and increase traction with an easy bolt on installation!

All of the ends are fitted with grease fittings for easy lubrication and they’re available powder coated in your choice of bright red or gloss black for a brilliant and durable finish.

Build Specifications: 

  • 1.00″ x .095″ wall DOM tubing formed to the shape of the OEM control arms for a 100% bolt in installation
  • Stronger, yet over three pounds lighter than stock
  • 3/4″ Del-Sphere pivot joints on the rear ends equipped with grease fittings for easy lubrication
  • CNC machined through sleeve and silver zinc plated steel spacers keep the Del-Sphere ends perfectly centered inside of the mounting brackets
  • Polyurethane bushed (fluted) ends on the front ends equipped with grease fittings for easy lubrication
  • Re-uses OEM mounting hardware, no need to drill out your car’s mounting brackets
  • Available powder coated in your choice of bright red or gloss black for a brilliant and durable finish

These combo ended control arms will wipe out most bind, yet keep the road noise increase minimal for a street driven car. The Del-Sphere pivot joints provide for “bind-free” handling performance.

The fluted polyurethane bushed ends are mounted onto the chassis (floor) mount for maximum road noise insulation.

Check out all of our performance suspension components for the 1972-1976 Ford Torino and Ranchero by clicking here.