Spohn Performance | Support Center

View Articles by Category

There are no sub categories
Add an article to this category

Category » Tech Support Info & FAQsrss button

Technical support articles and answers to frequently asked technical questions
(Page 2 of 7)     Prev | 1 | 2 | 3 | 4 | 5 | 6 | 7 | Next

There were 135 articles found in this category:

  1. questionDo you carry rear ends for applications other than what you have on your website?
    Yes, we carry the complete line of Moser & Strange Engineering rear ends and components. For more information on the complete selection available click here.
  2. questionDo you have a k-member to install a small or big block chevy engine in to a 1993-2002 GM F-Body?
    At this time the only set up we have for the standard small block and big block engine applications in a 1993-2002 GM F-Body is our tubular k-member with no motor mount pads installed. You will need to use a motor plate to mount the engine.
  3. questionDo you have any instructions or information on installing coil over shocks and springs on a 2010+ Camaro?
    See the .pdf attachment below for coil over spring and shock installation instructions for the 2010+ Chevrolet Camaro.
  4. questionDo you have any product tour videos I can watch?
    Product tour videos, etc. are available at http://tv.spohn.net
  5. questionDo you have installation tips for your 992 solid LSx motor mounts for the 1993-2002 F-Body Camaro & Firebird?
    When installing the SKU# 992 solid motor mounts you will need to keep everything loose until you have everything in place and all bolts and nuts started. You must loosen your transmission mount. Then install the motor mounts one side at a time just starting the bolts (keep everything loose). On ...
  6. questionDo you have the instructions Moser sends along with their 1982-2002 F-Body rear ends?
    Download the file attached below to view all of the instructions that Moser Engineering sends along with their 12 Bolt and Ford 9" rear ends for the 1982-2002 GM F-Body Camaro and Firebird.
  7. questionDo you offer a power rack and pinion option for your 1982-1992 F-Body Camaro Firebird k-members?
    As of this time we only offer the Pinto manual rack and pinion kit for the 1982-1992 F-Body Camaro and Firebird tubular k-members. The rack mounts for the Pinto manual rack are much different then what would be required for a power rack so you would not be able to mount your own power rack to o ...
  8. questionDo you offer any powder coated colors other than red or black?
    At this time we can only powder coat our parts in bright red or gloss black. If you would like a custom color and have someone locally who can do this for you then we can provide you our parts in bare metal. Feel free to contact us before ordering if you would like to go that route.
  9. questionDo your adjustable suspension pieces come set at stock length?
    Yes. All of our adjustable suspension pieces such as panhard bars, control arms, torque arms, a-arms, etc. are jig set at factory length. If you don't want to mess with any adjusting just install the parts as we shipped them to you and you'll be good to go.
  10. questionDo your roll cages and roll bars work in a convertible F-Body Camaro & Firebird?
    Yes, our roll bars and roll cages for the 1982-2002 F-Body Camaro and Firebird can be installed in a convertible car with some slight modifications by the installer. For detailed information and pictures click here. html sitemap
  11. questionDo your SKU# D94-02-RTB-QCSB traction bars for the 1994-2002 Dodge Ram 4x4 fit trucks besides the quad cab short bed?
    Our SKU# D94-02-RTB-QCSB Extreme Duty Rear Traction Bars for the 1994-2002 Dodge Ram 4x4 1500, 2500 and 3500 Quad Cab Short Bed will fit all other 1994-2002 Dodge Ram 4x4 trucks but they will NOT be a 100% bolt in installation. On trucks other than the quad cab short bed the front mounts will ...
  12. questionDo your tubular lower a-arms include steering stops? (82-92 F-Body, 78-87 G-Body, 82-03 S-10)
    Prior to 2010 steering stops were an option on our tubular front lower a-arms for the following vehicles: 1982-1992 GM F-Body 1978-1987 GM G-Body 1982-2003 GM S-10 (2WD) If you have a-arms manufactured prior to 2010 that do not have steering stops you can purchase our clamp on steering stop ...
  13. questionDoes your Pro-Series Rear Drag Sway Bar change the ride height?
    No. If you think your ride height has changed then you most likely have the u-bolts that go through the bushings tightened too much. If the u-bolts are over tightened it does not allow the sway bar to rotate in the bushings which binds up the rear suspension. This will cause a ride height chang ...
  14. questionFor the 1978-1987 GM G-Body & 1982-2003 S-10 (2WD) what is the difference between Standard & SuperTravel front upper ball joints?
    If you are ordering tubular front a-arms or a front end rebuild kit for the 1978-1987 GM G-Body or the 1982-2003 GM S-10 (2WD) you will have a choice between Standard or SuperTravel front upper ball joints. The Standard front upper ball joints are factory replacement ball joints. The SuperTrave ...
  15. questionFor the 2010+ Camaro do you have a list of all of the front and rear suspension torque settings and specifications?
    See the .pdf attachments below for a complete listing of front and rear suspension torque specifications and ratings for the 2010+ Chevrolet Camaro.
  16. questionHave you addressed the end link mount strength issue on your SKU# C10-221, C10-221-DEL, C10-222 & C10-222-DEL rear lower control arms for the 2010+ Camaro & 08-09 G8?
    Yes we have. The stock rear lower control arms are known to have strength issues with the rear sway bar end link mounting tabs. Many people have been having the rear sway bar end link mounting tab on the stock rear lower control arms on their 2010+ Camaro and 2008-2009 Pontiac G8 deforming, brea ...
  17. questionHow can I get a shipping price quote on a rear end?
    Ford 9" Rear Ends: Ford 9" rear ends ship via UPS Ground. We are unable to calculate the shipping charge on the website. You can place your order for the rear end and we will contact you for your approval of the UPS Ground shipping charge before processing your order. You can email your complet ...
  18. questionHow do I know if I need an adjustable panhard bar?
    Normally, if you will be running the stock rear end and will not be lowering your ride height then you do not "need" an adjustable panhard bar. If you plan to lower your ride height and/or install an aftermarket rear end then we suggest getting an adjustable panhard bar to allow you to properly ...
  19. questionHow do I know what size sway bars I have? I want to order bushings but don't know my bar diameter.
    1993-2002 GM F-Body Camaro and Firebird cars came from the factory with 30 mm front and 19 mm rear sway bars. For the 1982-1992 GM F-Body and most other vehicles the diameter of the sway bars varies depending on the vehicle's model, options and package. The best thing to do is measure the diame ...
  20. questionHow do I measure and know the length I need for a custom driveshaft?
    We can build a custom drive shaft for almost any application. To order a custom built driveshaft see our custom driveshaft page. Measurements: Follow these instructions to provide us with the information needed to build your driveshaft: 1. Enter your transmission type (ie. TH350, TH400, Pow ...
(Page 2 of 7)     Prev | 1 | 2 | 3 | 4 | 5 | 6 | 7 | Next